Eminence Logo

Eminence Legend BP102 10 Inch 200W Bass Speaker   

  • Write a Review

The Eminence Legend BP102 10" Bass Speaker delivers rich bass tone with a lot of punch. Recommended for professional bass guitar applications in seal...Click To Read More About This Product

Available 06-03-2017

  • Shipping (48 Contigous U.S. States)
  • Your Price :
  Reserve Now Notify Me When This is in Stock
Add to Wish List

Earn up to 375 reward points.

Recommended Accessories

Solid bass sound with tight lows.

The Eminence Legend BP102 10" Bass Speaker delivers rich bass tone with a lot of punch. Recommended for professional bass guitar applications in sealed or vented enclosures. The replacement speaker works well in single or multi-driver designs.

Use the Eminence Legend BP102 as a direct replacement speaker in the Ampeg SVT-810E, the Kustom Groove 4120, the Gallien-Krueger 4120 SBX, the Ashdown MAG 410T & MAG810T, and the Basson B410B speaker cabinets. Eminence recommends the Legend BP102 as a direct replacement in the Kustom Groove 310C, the Ampeg BA210SP, the Peavey Bam 210 combo amps.

  • Rich bass tone with good punch
  • Tight low-end sound
  • Recommended for sealed or vented enclosures

Put this Eminence bass speaker in the cart and make your bass cab sound better than new.


Legend BP102 10 Inch 200W Bass Speaker

  • Nominal Basket Diameter: 10", 254mm
    Nominal Impedance*: 8 ohms
    Power Rating**: 200W
    Resonance: 35Hz
    Usable Frequency Range: 44Hz-4kHz
    Sensitivity***: 92
    Magnet Weight: 38 oz.
    Gap Height: 0.312", 7.92mm
    Voice Coil Diameter : 2", 50.8mm

    Resonant Frequency (fs): 35Hz
    DC Resistance (Re): 5.59
    Coil Inductance (Le): 0.83mH
    Mechanical Q (Qms): 5.36
    Electromagnetic Q (Qes): 0.47
    Total Q (Qts): 0.43
    Compliance Equivalent Volume (Vas): 91.2 liters / 3.2 cu. ft.
    Peak Diaphragm Displacement Volume (Vd): 207cc
    Mechanical Compliance of Suspension (Cms): 0.54mm/N
    BL Product (BL): 10.0 T-M
    Diaphragm Mass inc. Airload (Mms): 38 grams
    Efficiency Bandwidth Product (EBP): 75
    Maximum Linear Excursion (Xmax): 6.2mm
    Surface Area of Cone (Sd): 334.5 cm2
    Maximum Mechanical Limit (Xlim): 10.0mm

    Mounting Information
    Recommended Enclosure Volume
    Sealed: 14-28 liters/ 0.5-1 cu.ft.
    Vented: 25.5-62 liters/ 0.9-2.2 cu.ft.
    Overall Diameter: 10.08", 256.1mm
    Baffle Hole Diameter: 9.05", 229.7mm
    Front Sealing Gasket: fitted as standard
    Rear Sealing Gasket:
    Mounting Holes Diameter: 0.25", 6.4mm
    Mounting Holes B.C.D.: 9.66", 245.4mm
    Depth: 4.25", 108mm
    Net Weight: 8.9 lb., 4 kg
    Shipping Weight: 9.1 lbs., 4.1 kg

    Materials of Construction
    Copper voice coil
    Polyimide former
    Ferrite magnet
    Non-vented core
    Pressed steel basket
    Paper Cone
    Cloth cone edge
    Zurette dust cap

    *Please inquire about alternative impedances.
    **Multiple units exceed published rating evaluated under EIA 426A noise source and test standard while in a free-air, non-temperature controlled environment.
    ***The average output across the usable frequency range when applying 1W/1M into the nominal impedance. Ie: 2.83V/8ohms, 4V/16ohms.
    Eminence response curves are measured under the following conditions: All speakers are tested at 1w/1m using a variety of test set-ups for the appropriate impedance | LMS using 0.25" supplied microphone (software
    calibrated) mounted 1m from wall/baffle | 2ft. X 2ft. baffle is built into the wall with the speaker mounted flush against a steel ring for minimum diffraction | Hafler P1500 Trans-Nova amplifier | 2700 cu.ft. chamber with
    fiberglass on all six surfaces (three with custom-made wedges)

© Woodwind & Brasswind. All rights reserved.     Terms & Conditions | Privacy Policy

You are changing the Ship-To country.

Our product catalog varies by country due to manufacturer restrictions. If you change the Ship-To country, some or all of the items in your cart may not ship to the new destination.